CUBICON, 3D Printer & AI Robotics Company
3D Printer
Frequently asked questions and answers are available.
Contact us if there is no information you want, please ask it on the inquiry board.Total : 71, [4/5] Page
[Single Plus] The filament cannot be removed from the nozzle body.
Disassemble the extruder upper and remove debris will correct this problem.
1. Power off the printer.
2. Loosen the extruder top mounting bolt until it is lifted slightly.
3. Hold both sides of the bottom by hand and apply a slight downward force to separate them.
4. Use the 2mm wrench to remove the top cover on the back. (The 2mm wrench is in the toolbox.)
5. Remove the mounting bolt in the middle.
6. Use the 2mm wrench to loosen two bolts and detach the filament guide. (The 2mm wrench is in the toolbox.)
7. Use the 2.5mm wrench to loosen one bolt and detach the lever.
* Loosen the bold with the lever pressed.
8. Remove debris.
▶ Check more details on YouTube. (See 0:00~2:30 part in the video below.)
- URL: https://youtu.be/OTj6VSrqxos
[Single Plus] The filament is not attached to the bed.
In some cases, the temperature for the filament you want to use is not set, so please check again.
Also, it is recommended to check because it is related to the cleaning of the extruder or the nozzle life.
▶ Service temperature table by Cubicon filament (recommended)
Filament
|
Nozzle
|
Bed
|
(Material)
|
Service Temperature
|
Service Temperature
|
ABS
|
240℃
|
115℃
|
ABS-A100
|
230℃
|
100℃
|
PLA
|
210℃
|
65℃
|
PLA-i21
|
210℃
|
65℃
|
PETG
|
230℃
|
80℃
|
TPU
|
230℃
|
65℃
|
▶ Once you fully understand the Cubicreator basic tutorial, you can use the printer easier.
[Cubicon]Cubicreator3 basic tutorial
- URL: https://youtu.be/kP36fJiU1gQ
[Cubicon]Cubicreator4 basic tutorial
- URL: https://youtu.be/7ND7lERdYTc
Additional solution) Replace the extruder nozzle kit (See the detailed method ☞ Click)
1. Unload the fitted filament. (See the detailed method ☞ Click)
1-1. Select [Filament] on the printer screen.
1-2. Select [Filament] on the printer screen.
1-3. Select the type of filament fitted, then select when the [Start] button is active.
1-4. When the filaments automatically disengage after performing the automatic unloading motion, open the printer top cover, press the left lever of the extruder, and completely remove the filament.
2. Turn off the printer power.
3. Loosen the extruder top mounting bolt until it is lifted slightly.
4. Hold both sides of the bottom by hand and apply a slight downward force to separate them.
5. Remove the nozzle kit at the extruder bottom using the socket wrench tool. (The socket wrench tool is in the toolbox.)
6. Prepare the nozzle kit to replace. * It is recommended to keep an extra nozzle kit at all times.
7. Fix the nozzle kit using the socket wrench tool. (The socket wrench tool is in the toolbox.)
* Excessive force may cause damage.
8. Insert the extruder, that the nozzle has been replaced, from the bottom aligning with the fan hole.
9. Fix the extruder top mounting bolt.
10. Power on the printer.
11. Cut off the end of the filament to make the supply smooth.
12. With the left lever pressed, insert the filament until it is no longer inserted (approximately 10 cm).
▶ Check more details on YouTube.
- URL: https://youtu.be/Khw38aKCdMU
▶ Notes
A nozzle is consumables.
The replacement is recommended every six months for 3D printer businesses and every one year for individual users.
However, the replacement cycle may vary depending on the usage.
The additional nozzle is included in the toolbox as a basic component when purchasing a printer.
An additional purchase is available at the Cubicon website or retail stores.
For model 310F, the nozzle tip replacement is conducted at the extruder repair center.
(Cubicon Customer Service Center Application: 1661-4371)
[Single Plus] The nozzle scratches on the bed.
This problem can be solved by replacing the nozzle tip.
If the nozzle tip is crushed or damaged, the leveling may fail, or the nozzle may scratch on the bed.
Solution 1) The extruder nozzle kit replacement (See the detailed method ☞ Click)
1. Unload the fitted filament. (See the detailed method ☞ Click)
1-1. Select [Filament] on the printer screen.
1-2. Select [Filament] on the printer screen.
1-3. Select the type of filament fitted, then select when the [Start] button is active.
1-4. When the filaments automatically disengage after performing the automatic unloading motion,
open the printer top cover, press the left lever of the extruder, and completely remove the filament.
2. Turn off the printer power.
3. Loosen the extruder top mounting bolt until it is lifted slightly.
4. Hold both sides of the bottom by hand and apply a slight downward force to separate them.
5. Remove the nozzle kit at the extruder bottom using the socket wrench tool. (The socket wrench tool is in the toolbox.)
6. Prepare the nozzle kit to replace. * It is recommended to keep an extra nozzle kit at all times.
7. Fix the nozzle kit using the socket wrench tool. (The socket wrench tool is in the toolbox.)
* Excessive force may cause damage.
8. Insert the extruder, that the nozzle has been replaced, from the bottom aligning with the fan hole.
9. Fix the extruder top mounting bolt.
10. Power on the printer.
11. Cut off the end of the filament to make the supply smooth.
12. With the left lever pressed, insert the filament until it is no longer inserted (approximately 10 cm).
▶ Check more details on YouTube.
- URL: https://youtu.be/Khw38aKCdMU
▶ Notes
A nozzle is consumables.
The replacement is recommended every six months for 3D printer businesses and every one year for individual users.
However, the replacement cycle may vary depending on the usage.
The additional nozzle is included in the toolbox as a basic component when purchasing a printer.
An additional purchase is available at the Cubicon website or retail stores.
For model 310F, the nozzle tip replacement is conducted at the extruder repair center.
(Cubicon Customer Service Center Application: 1661-4371)
[Single Plus] There is a difference between modeling and output.
If the modeling file is not in the perfect solid shape, the output may be printed partially different shape than the modeling file.
Solution 1) Adjust two options
Simple errors can be corrected by adjusting options.
(1) Setting > Preferences > Rendering > Check the box of Drawing the Back
(Uncheck it first if it was checked, then recheck it.)
(2) Check Detailed Options > Nash Adjustment > Model Adjustment (Keep Disconnected Faces)
After adjusting the above two options, preview the output by clicking the [Output Preparation].
If the error is still not corrected, follow the below Solution 2.
Solution 2) Modifying the modeling file to a complete solid shape
If it is not a simple error that can be corrected by just adjusting the options, please correct the modeling file itself to the perfect solid shape and retry.
[Single Plus] After updating to Cubicreator4 version, the slicing stops at 99%.
It is because an error occurred while saving the slicing information to the database.
The issue has been corrected with the latest version of Cubicreator4.
You can download the latest version of Cubicreator4 from the Cubicon website > Technical Support > Technical Data Center.
[Single Plus] I want to initialize the firmware.
It is how to update to the latest version after the Firmware initialization.
1. Power off the printer.
2. Power on the printer with the RESET button pressed on the front.
3. Press the RESET button until the message 'Recovery Firmware' appears on the screen (LCD).
4. Download the latest firmware and proceed with the update.
[Single Plus] I want to update the firmware.
1. Download the firmware to update on the Cubicon website. (3dcubicon.co.kr > Technical Support > Technical Data Room > Required File Download)
2. Unzip the downloaded file and rename the folder to 'firmware' using the full lowercase letters, then copy it to USB.
3. Connect USB to equipment.
4. On the printer screen, press in the order of Settings > Firmware > Download to proceed with the firmware update. * The update takes about 5 minutes.
5. The printer will restart automatically. * You can check if the update has been successful in the Info menu.
▶ Check more details on YouTube.
- URL: https://youtu.be/Q1pnZlBQdEE
[Single Plus] It says No Firmware.
1. Open the rear cover of the printer and release the Micro SD card mounted on the mainboard.
2. Format the Micro SD card.
3. Download and unzip 310F Micro SD card files from the Technical Data Room.
3dcubicon.co.kr > Technical Support > Technical Data Room
4. Move all files in the unzipped folder to the Micro SD card and mount it back to the mainboard.
5. After powering on the printer, check if the 'No Firmware' has disappeared.
▶ Check more details on YouTube.
- URL: https://youtu.be/7ta8_A_d07I
[Single Plus] It says auto-leveling failed.
It can be solved by cleaning the extruder or replacing the nozzle kit.
Solution 1) Cleaning the extruder (See the detailed method ☞ Click)
1. Unload the fitted filament. (See the detailed method ☞ Click)
1-1. Select [Filament] on the printer screen.
1-2. Select [Filament] on the printer screen.
1-3. Select the type of filament fitted, then select when the [Start] button is active.
1-4. When the filaments automatically disengage after performing the automatic unloading motion, open the printer top cover, press the left lever of the extruder, and completely remove the filament.
2. Turn off the printer power.
3. Loosen the extruder top mounting bolt until it is lifted slightly.
4. Hold both sides of the bottom by hand and apply a slight downward force to separate them.
5. Before the extruder gets cool down, move the cleaning tool up and down and start the cleaning. (The cleaning tool is in the toolbox.)
6. Insert the extruder that has finished the cleaning, from the bottom aligning with the fan hole.
7. Fix the extruder top mounting bolt.
9. Cut off the end of the filament to make the supply smooth.
▶ Check
more details on YouTube.
- URL: https://youtu.be/6f40VZk9yWs
Solution 2) The extruder nozzle kit replacement (See the detailed method ☞ Click)
1. Unload the fitted filament. (See the detailed method ☞ Click)
1-1. Select [Filament] on the printer screen.
1-2. Select [Filament] on the printer screen.
1-3. Select the type of filament fitted, then select when the [Start] button is active.
1-4. When the filaments automatically disengage after performing the automatic unloading motion, open the printer top cover, press the left lever of the extruder, and completely remove the filament.
2. Turn off the printer power.
3. Loosen the extruder top mounting bolt until it is lifted slightly.
4. Hold both sides of the bottom by hand and apply a slight downward force to separate them.
5. Remove the nozzle kit at the extruder bottom using the socket wrench tool. (The socket wrench tool is in the toolbox.)
6. Prepare the nozzle kit to replace.
* It is recommended to keep an extra nozzle kit at all times.
7. Fix the nozzle kit using the socket wrench tool. (The socket wrench tool is in the toolbox.)
* Excessive force may cause damage.
8. Insert the extruder, that the nozzle has been replaced, from the bottom aligning with the fan hole.
9. Fix the extruder top mounting bolt.
10. Power on the printer.
11. Cut off the end of the filament to make the supply smooth.
12. With the left lever pressed, insert the filament until it is no longer inserted (approximately 10 cm).
▶ Check more details on YouTube.
- URL: https://youtu.be/6f40VZk9yWs
If
auto-leveling fails continuously even after cleaning the extruder using the
above method, please follow the below solution 2.
Solution 2) Replace the extruder nozzle kit (See the detailed method ☞ Click)
1. Unload the fitted filament. (See the detailed method ☞ Click)
1-1. Select [Filament] on the printer screen.
1-2. Select [Filament] on the printer screen.
1-3. Select the type of filament fitted, then select when the [Start] button is active.
1-4. When the filaments automatically disengage after performing the automatic unloading motion,
open the printer top cover, press the left lever of the extruder, and completely remove the filament.
2. Turn off the printer power.
3. Loosen the extruder top mounting bolt until it is lifted slightly.
4. Hold both sides of the bottom by hand and apply a slight downward force to separate them.
5. Remove the nozzle kit at the extruder bottom using the socket wrench tool. (The socket wrench tool is in the toolbox.)
6. Prepare the nozzle kit to replace. * It is recommended to keep an extra nozzle kit at all times.
7. Fix the nozzle kit using the socket wrench tool. (The socket wrench tool is in the toolbox.)
* Excessive force may cause damage.
8. Insert the extruder, that the nozzle has been replaced, from the bottom aligning with the fan hole.
9. Fix the extruder top mounting bolt.
10. Power on the printer.
11. Cut off the end of the filament to make the supply smooth.
12. With the left lever pressed, insert the filament until it is no longer inserted (approximately 10 cm).
▶ Check more details on YouTube.
- URL: https://youtu.be/Khw38aKCdMU
▶ Notes
A nozzle is consumables.
The replacement is recommended every six months for 3D printer businesses and every one year for individual users.
However, the replacement cycle may vary depending on the usage.
The additional nozzle is included in the toolbox as a basic component when purchasing a printer.
An additional purchase is available at the Cubicon website or retail stores.
[Single Plus] It makes a noise (rattle) and auto-leveling fail.
Auto-leveling is carried out in such a way that it applies an electric current to the silver part of the bed surface.
Cleaning the extruder can solve this problem.
Solution 1) Cleaning the extruder (See the detailed method ☞ Click)
1. Unload the fitted filament. (See the detailed method ☞ Click)
1-1. Select [Filament] on the printer screen.
1-2. Select [Filament] on the printer screen.
1-3. Select the type of filament fitted, then select when the [Start] button is active.
1-4. When the filaments automatically disengage after performing the automatic unloading motion, open the printer top cover, press the left lever of the extruder, and completely remove the filament.
2. Turn off the printer power.
3. Loosen the extruder top mounting bolt until it is lifted slightly.
4. Hold both sides of the bottom by hand and apply a slight downward force to separate them.
5. Before the extruder gets cool down, move the cleaning tool up and down and start the cleaning. (The cleaning tool is in the toolbox.)
6. Insert the extruder that has finished the cleaning, from the bottom aligning with the fan hole.
7. Fix the extruder top mounting bolt.
9. Cut off the end of the filament to make the supply smooth.
▶ Check
more details on YouTube.
- URL: https://youtu.be/6f40VZk9yWs
Solution 2) The extruder nozzle kit replacement (See the detailed method ☞ Click)
1. Unload the fitted filament. (See the detailed method ☞ Click)
1-1. Select [Filament] on the printer screen.
1-2. Select [Filament] on the printer screen.
1-3. Select the type of filament fitted, then select when the [Start] button is active.
1-4. When the filaments automatically disengage after performing the automatic unloading motion, open the printer top cover, press the left lever of the extruder, and completely remove the filament.
2. Turn off the printer power.
3. Loosen the extruder top mounting bolt until it is lifted slightly.
4. Hold both sides of the bottom by hand and apply a slight downward force to separate them.
5. Remove the nozzle kit at the extruder bottom using the socket wrench tool. (The socket wrench tool is in the toolbox.)
6. Prepare the nozzle kit to replace.
* It is recommended to keep an extra nozzle kit at all times.
7. Fix the nozzle kit using the socket wrench tool. (The socket wrench tool is in the toolbox.)
* Excessive force may cause damage.
8. Insert the extruder, that the nozzle has been replaced, from the bottom aligning with the fan hole.
9. Fix the extruder top mounting bolt.
10. Power on the printer.
11. Cut off the end of the filament to make the supply smooth.
12. With the left lever pressed, insert the filament until it is no longer inserted (approximately 10 cm).
▶ Check more details on YouTube.
- URL: https://youtu.be/6f40VZk9yWs
If
auto-leveling fails continuously even after cleaning the extruder using the
above method, please follow the below solution 2.
Solution 2) Replace the extruder nozzle kit (See the detailed method ☞ Click)
1. Unload the fitted filament. (See the detailed method ☞ Click)
1-1. Select [Filament] on the printer screen.
1-2. Select [Filament] on the printer screen.
1-3. Select the type of filament fitted, then select when the [Start] button is active.
1-4. When the filaments automatically disengage after performing the automatic unloading motion,
open the printer top cover, press the left lever of the extruder, and completely remove the filament.
2. Turn off the printer power.
3. Loosen the extruder top mounting bolt until it is lifted slightly.
4. Hold both sides of the bottom by hand and apply a slight downward force to separate them.
5. Remove the nozzle kit at the extruder bottom using the socket wrench tool. (The socket wrench tool is in the toolbox.)
6. Prepare the nozzle kit to replace. * It is recommended to keep an extra nozzle kit at all times.
7. Fix the nozzle kit using the socket wrench tool. (The socket wrench tool is in the toolbox.)
* Excessive force may cause damage.
8. Insert the extruder, that the nozzle has been replaced, from the bottom aligning with the fan hole.
9. Fix the extruder top mounting bolt.
10. Power on the printer.
11. Cut off the end of the filament to make the supply smooth.
12. With the left lever pressed, insert the filament until it is no longer inserted (approximately 10 cm).
▶ Check more details on YouTube.
- URL: https://youtu.be/Khw38aKCdMU
▶ Notes
A nozzle is consumables.
The replacement is recommended every six months for 3D printer businesses and every one year for individual users.
However, the replacement cycle may vary depending on the usage.
The additional nozzle is included in the toolbox as a basic component when purchasing a printer.
[Single Plus] Even after cleaning the leveling sensor, auto-leveling keeps fails.
Auto-leveling is carried out in such a way that it applies an electric current to the silver part of the bed surface.
Cleaning the extruder can solve this problem.
Solution 1) Cleaning the extruder (See the detailed method ☞ Click)
1. Unload the fitted filament. (See the detailed method ☞ Click)
1-1. Select [Filament] on the printer screen.
1-2. Select [Filament] on the printer screen.
1-3. Select the type of filament fitted, then select when the [Start] button is active.
1-4. When the filaments automatically disengage after performing the automatic unloading motion, open the printer top cover, press the left lever of the extruder, and completely remove the filament.
2. Turn off the printer power.
3. Loosen the extruder top mounting bolt until it is lifted slightly.
4. Hold both sides of the bottom by hand and apply a slight downward force to separate them.
5. Before the extruder gets cool down, move the cleaning tool up and down and start the cleaning. (The cleaning tool is in the toolbox.)
6. Insert the extruder that has finished the cleaning, from the bottom aligning with the fan hole.
7. Fix the extruder top mounting bolt.
9. Cut off the end of the filament to make the supply smooth.
▶ Check
more details on YouTube.
- URL: https://youtu.be/6f40VZk9yWs
If auto-leveling fails continuously even after cleaning the extruder using the above method, please follow the below solution 2.
Solution 2) The extruder nozzle kit replacement (See the detailed method ☞ Click)
1. Unload the fitted filament. (See the detailed method ☞ Click)
1-1. Select [Filament] on the printer screen.
1-2. Select [Filament] on the printer screen.
1-3. Select the type of filament fitted, then select when the [Start] button is active.
1-4. When the filaments automatically disengage after performing the automatic unloading motion, open the printer top cover, press the left lever of the extruder, and completely remove the filament.
2. Turn off the printer power.
3. Loosen the extruder top mounting bolt until it is lifted slightly.
4. Hold both sides of the bottom by hand and apply a slight downward force to separate them.
5. Remove the nozzle kit at the extruder bottom using the socket wrench tool. (The socket wrench tool is in the toolbox.)
6. Prepare the nozzle kit to replace.
* It is recommended to keep an extra nozzle kit at all times.
7. Fix the nozzle kit using the socket wrench tool. (The socket wrench tool is in the toolbox.)
* Excessive force may cause damage.
8. Insert the extruder, that the nozzle has been replaced, from the bottom aligning with the fan hole.
9. Fix the extruder top mounting bolt.
10. Power on the printer.
11. Cut off the end of the filament to make the supply smooth.
12. With the left lever pressed, insert the filament until it is no longer inserted (approximately 10 cm).
▶ Check more details on YouTube.
- URL: https://youtu.be/6f40VZk9yWs
If
auto-leveling fails continuously even after cleaning the extruder using the
above method, please follow the below solution 2.
Solution 2) Replace the extruder nozzle kit (See the detailed method ☞ Click)
1. Unload the fitted filament. (See the detailed method ☞ Click)
1-1. Select [Filament] on the printer screen.
1-2. Select [Filament] on the printer screen.
1-3. Select the type of filament fitted, then select when the [Start] button is active.
1-4. When the filaments automatically disengage after performing the automatic unloading motion,
open the printer top cover, press the left lever of the extruder, and completely remove the filament.
2. Turn off the printer power.
3. Loosen the extruder top mounting bolt until it is lifted slightly.
4. Hold both sides of the bottom by hand and apply a slight downward force to separate them.
5. Remove the nozzle kit at the extruder bottom using the socket wrench tool. (The socket wrench tool is in the toolbox.)
6. Prepare the nozzle kit to replace. * It is recommended to keep an extra nozzle kit at all times.
7. Fix the nozzle kit using the socket wrench tool. (The socket wrench tool is in the toolbox.)
* Excessive force may cause damage.
8. Insert the extruder, that the nozzle has been replaced, from the bottom aligning with the fan hole.
9. Fix the extruder top mounting bolt.
10. Power on the printer.
11. Cut off the end of the filament to make the supply smooth.
12. With the left lever pressed, insert the filament until it is no longer inserted (approximately 10 cm).
▶ Check more details on YouTube.
- URL: https://youtu.be/Khw38aKCdMU
▶ Notes
A nozzle is consumables.
The replacement is recommended every six months for 3D printer businesses and every one year for individual users.
However, the replacement cycle may vary depending on t
[Single Plus] The \'Auto-leveling Check\' keeps appeared when printing out.
Auto-leveling is carried out in such a way that it applies an electric current to the silver part of the bed surface.
Cleaning the extruder can solve this problem.
Solution 1) Cleaning the extruder (See the detailed method ☞ Click)
1. Unload the fitted filament. (See the detailed method ☞ Click)
1-1. Select [Filament] on the printer screen.
1-2. Select [Filament] on the printer screen.
1-3. Select the type of filament fitted, then select when the [Start] button is active.
1-4. When the filaments automatically disengage after performing the automatic unloading motion,
open the printer top cover, press the left lever of the extruder, and completely remove the filament.
2. Turn off the printer power.
3. Loosen the extruder top mounting bolt until it is lifted slightly.
4. Hold both sides of the bottom by hand and apply a slight downward force to separate them.
5. Before the extruder gets cool down, move the cleaning tool up and down and start the cleaning. (The cleaning tool is in the toolbox.)
6. Insert the extruder that has finished the cleaning, from the bottom aligning with the fan hole.
7. Fix the extruder top mounting bolt.
9. Cut off the end of the filament to make the supply smooth.
▶ Check
more details on YouTube.
- URL: https://youtu.be/6f40VZk9yWs
If auto-leveling fails continuously even after cleaning the extruder using the above method, please follow the below solution 2.
Solution 2) The extruder nozzle kit replacement (See the detailed method ☞ Click)
1. Unload the fitted filament. (See the detailed method ☞ Click)
1-1. Select [Filament] on the printer screen.
1-2. Select [Filament] on the printer screen.
1-3. Select the type of filament fitted, then select when the [Start] button is active.
1-4. When the filaments automatically disengage after performing the automatic unloading motion, open the printer top cover, press the left lever of the extruder, and completely remove the filament.
2. Turn off the printer power.
3. Loosen the extruder top mounting bolt until it is lifted slightly.
4. Hold both sides of the bottom by hand and apply a slight downward force to separate them.
5. Remove the nozzle kit at the extruder bottom using the socket wrench tool. (The socket wrench tool is in the toolbox.)
6. Prepare the nozzle kit to replace.
* It is recommended to keep an extra nozzle kit at all times.
7. Fix the nozzle kit using the socket wrench tool. (The socket wrench tool is in the toolbox.)
* Excessive force may cause damage.
8. Insert the extruder, that the nozzle has been replaced, from the bottom aligning with the fan hole.
9. Fix the extruder top mounting bolt.
10. Power on the printer.
11. Cut off the end of the filament to make the supply smooth.
12. With the left lever pressed, insert the filament until it is no longer inserted (approximately 10 cm).
▶ Check more details on YouTube.
- URL: https://youtu.be/6f40VZk9yWs
If
auto-leveling fails continuously even after cleaning the extruder using the
above method, please follow the below solution 2.
Solution 2) Replace the extruder nozzle kit (See the detailed method ☞ Click)
1. Unload the fitted filament. (See the detailed method ☞ Click)
1-1. Select [Filament] on the printer screen.
1-2. Select [Filament] on the printer screen.
1-3. Select the type of filament fitted, then select when the [Start] button is active.
1-4. When the filaments automatically disengage after performing the automatic unloading motion,
open the printer top cover, press the left lever of the extruder, and completely remove the filament.
2. Turn off the printer power.
3. Loosen the extruder top mounting bolt until it is lifted slightly.
4. Hold both sides of the bottom by hand and apply a slight downward force to separate them.
5. Remove the nozzle kit at the extruder bottom using the socket wrench tool. (The socket wrench tool is in the toolbox.)
6. Prepare the nozzle kit to replace. * It is recommended to keep an extra nozzle kit at all times.
7. Fix the nozzle kit using the socket wrench tool. (The socket wrench tool is in the toolbox.)
* Excessive force may cause damage.
8. Insert the extruder, that the nozzle has been replaced, from the bottom aligning with the fan hole.
9. Fix the extruder top mounting bolt.
10. Power on the printer.
11. Cut off the end of the filament to make the supply smooth.
12. With the left lever pressed, insert the filament until it is no longer inserted (approximately 10 cm).
▶ Check more details on YouTube.
- URL: https://youtu.be/Khw38aKCdMU
▶ Notes
A nozzle is consumables.
[Single Plus] The filament goes inwards.
Mostly that is because the gear is loosened and does not work, so reassemble and fix the gear again.
[Single Plus] I want to remove the filament fitted.
1. Select [Filament] on the printer screen.
2. Select the type of filament fitted and select the [Start] button when it is activated.
3. The printer automatically proceeds the unloading motion.
4. When the filaments automatically disengage, open the printer top cover, press the left lever of the extruder, and completely remove the filament.
5. The fitted filament has been removed successfully.
▶ Check more details on YouTube. (See 0:00~1:08 part in the video below.)
- URL: https://youtu.be/6f40VZk9yWs
[Single Plus] The filament keeps twisting in the filament box.
All of the filaments of Cubicon use a machine-winding method, and they are thoroughly inspected to prevent them from being shipped twisted or tangled before shipment.
However, there may be a problem depending on how to use/store the filament, so please fully understand the following precautions.
- The filament is weak against moisture. If it is not in use, please store it in the provided zipper pack (it includes a dehumidifying agent).
- If it is the first use of the filament, be careful the filament is not released when removing the fastening tape.
- When using the filament for the first time, the end is bent a lot, so cut with scissors and use it.
At this time, hold the part that does not cut and cut it using scissors to prevent tangling.
- Insert the filament end that is not inserted into the equipment into a nearby spool hole.
- Tangling may occur if the filament is stored untied. If the filament is already loose, loosen it up enough additionally and then rewind it.
▶ Check more details on YouTube.
URL: https://youtu.be/Al0i_3192cM
COPYRIGHT (C) 2020 CUBICON ALL RIGHTS RESERVED